{"id":5184,"date":"2026-05-30T01:58:10","date_gmt":"2026-05-30T09:58:10","guid":{"rendered":"https:\/\/changyupump.com\/?p=5184"},"modified":"2026-05-30T01:58:11","modified_gmt":"2026-05-30T09:58:11","slug":"what-is-the-static-pressure-of-the-centrifugal-pump-and-how-to-calculate-it","status":"publish","type":"post","link":"https:\/\/changyupump.com\/id\/blog\/what-is-the-static-pressure-of-the-centrifugal-pump-and-how-to-calculate-it\/","title":{"rendered":"What Is the Static Pressure of the Centrifugal Pump and How to Calculate It?"},"content":{"rendered":"\n<h2 class=\"wp-block-heading\">Introduction<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">In centrifugal pump technology, the term <strong>pressure always refers to static pressure<\/strong>. This definition, established by DIN EN ISO 17769-1:2012 (formerly EN 12723:2000), is the foundation upon which all pump pressure measurements, calculations, and performance evaluations are built. Yet it is also the source of persistent confusion among engineers, technicians, and students alike. When a pressure gauge is mounted on a pump&#8217;s suction or discharge nozzle, what is it actually measuring? Why does the gauge reading differ from the total energy the fluid possesses? And how should static pressure be correctly calculated at the inlet and outlet cross-sections?<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">These questions matter because static pressure is the basis for determining a pump&#8217;s total developed head, assessing its cavitation risk through NPSH calculations, and verifying whether the pump is operating at its design duty point. A pressure measurement that ignores the kinetic energy (velocity head) and potential energy (geodetic elevation head) of the fluid will misrepresent the true hydraulic conditions at the pump&#8217;s inlet and outlet. Changyu Pump engineers have observed in field installations that improperly vented measurement lines are among the most common sources of error in pump pressure readings, often leading to incorrect NPSHA calculations and misdiagnosed cavitation problems.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This guide provides a structured reference covering the definition of static pressure, its relationship to dynamic and total pressure through Bernoulli&#8217;s principle, the standard calculation formulas with worked examples, and the critical connection between inlet static pressure and NPSH. <\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"1000\" height=\"750\" src=\"https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It.webp\" alt=\"What Is the Static Pressure of the Centrifugal Pump and How to Calculate It?\" class=\"wp-image-5636\" srcset=\"https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It.webp 1000w, https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It-300x225.webp 300w, https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It-150x113.webp 150w, https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It-768x576.webp 768w, https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It-16x12.webp 16w\" sizes=\"auto, (max-width: 1000px) 100vw, 1000px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">1. What Is Static Pressure in a Centrifugal Pump?<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">1.1 Physical Definition<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">In fluid mechanics, <strong>static pressure<\/strong> is the pressure component that acts equally in all directions at a point within a fluid, independent of the fluid&#8217;s velocity. It is the pressure that would be measured by a pressure gauge moving with the fluid. In the context of a centrifugal pump, static pressure represents the potential energy per unit volume stored in the fluid\u2014the pressure that the pump must overcome on the suction side (to draw fluid in) and that it generates on the discharge side (to push fluid through the system).<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Static pressure should not be confused with the pressure that a stationary fluid exerts. In a moving fluid, static pressure coexists with dynamic pressure (velocity head), and it is the sum of these two components\u2014plus the potential energy from elevation\u2014that constitutes the fluid&#8217;s total mechanical energy per unit volume. A pump adds energy to the fluid, and understanding how that energy is partitioned between static and dynamic components is essential to interpreting pump performance.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1.2 The Standard Definition in Centrifugal Pump Technology<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The European standard EN 12723:2000 (now superseded by DIN EN ISO 17769-1:2012) establishes the terminology that governs how pressure is defined and measured in centrifugal pump applications. The standard specifies that:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>ps<\/strong> \u2014 static pressure at the pump inlet (suction) cross-section<\/li>\n\n\n\n<li><strong>pd<\/strong> \u2014 static pressure at the pump outlet (discharge) cross-section<\/li>\n\n\n\n<li><strong>ps,PG \/ pd,PG<\/strong> \u2014 pressure gauge readings at the inlet and outlet, respectively<\/li>\n\n\n\n<li><strong>pb<\/strong> \u2014 barometric (atmospheric) pressure<\/li>\n\n\n\n<li><strong>pV<\/strong> \u2014 vapour pressure of the pumped liquid at the operating temperature<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The key distinction is that <strong>ps and pd represent the static pressure at the actual pump inlet and outlet cross-sections<\/strong>, which are not the same as the pressure gauge readings taken at the measurement taps. The gauge reading must be corrected for the elevation difference between the gauge and the pump cross-section, and in certain measurement configurations, for the density of the fluid in the measurement line.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1.3 Gauge Pressure vs. Absolute Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Static pressure can be expressed in two reference frames. <strong>Gauge pressure<\/strong> is measured relative to the local atmospheric pressure and is the reading displayed by a standard pressure gauge. <strong>Absolute pressure<\/strong> is measured relative to a perfect vacuum and is the relevant quantity for thermodynamic calculations, including cavitation analysis and NPSH determination.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In centrifugal pump technology, the static pressures specified in the standard are typically gauge pressures. However, for NPSH calculations, absolute pressure must be used. The conversion between the two is straightforward but essential:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>Absolute Pressure = Gauge Pressure + Atmospheric Pressure<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">For a pump operating with a suction gauge reading of -0.3 bar (gauge) at sea level (atmospheric pressure \u2248 1.013 bar), the absolute pressure at the suction is approximately 0.713 bar. If this value falls below the liquid&#8217;s vapour pressure at the operating temperature, cavitation will occur.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1.4 The Fundamental Insight: What the Pressure Gauge Actually Measures<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A <strong>pressure gauge connected to a pump measures only the static pressure<\/strong> in the pipe. It does not capture the kinetic energy per unit volume (\u00bd\u03c1v\u00b2, the velocity head) that the fluid possesses by virtue of its motion. This is the most frequently misunderstood aspect of pump pressure measurement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The total energy per unit volume of the fluid at any cross-section is given by Bernoulli&#8217;s equation:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ptotal = pstatic + \u00bd\u03c1v\u00b2 + \u03c1gh<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">Where:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>pstatic<\/strong> = static pressure (gauge reading, corrected for elevation)<\/li>\n\n\n\n<li><strong>\u00bd\u03c1v\u00b2<\/strong> = dynamic pressure (velocity head)<\/li>\n\n\n\n<li><strong>\u03c1gh<\/strong> = potential energy from elevation (geodetic head)<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">When the pipe diameter at the suction and discharge nozzles differs\u2014as it often does\u2014the velocity component changes, and a gauge reading alone will not correctly represent the change in total energy across the pump. This is why pump total head must be calculated using the sum of static pressure, velocity head, and geodetic elevation head at both the suction and discharge cross-sections.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">2. Static Pressure vs. Dynamic Pressure vs. Total Pressure<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">2.1 Three Components of Fluid Energy<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">In a flowing fluid, the total mechanical energy per unit volume is the sum of three independent components:<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Pressure Type<\/th><th>Symbol<\/th><th>Physical Meaning<\/th><th>What It Represents<\/th><th>Formula<\/th><\/tr><\/thead><tbody><tr><td><strong>Static Pressure<\/strong><\/td><td>ps<\/td><td>Pressure exerted uniformly in all directions<\/td><td>Potential energy per unit volume stored in the fluid<\/td><td>ps (gauge reading, corrected for elevation)<\/td><\/tr><tr><td><strong>Dynamic Pressure<\/strong><\/td><td>pdyn<\/td><td>Pressure due to fluid motion<\/td><td>Kinetic energy per unit volume<\/td><td>\u00bd\u03c1v\u00b2<\/td><\/tr><tr><td><strong>Total Pressure<\/strong><\/td><td>ptot<\/td><td>Sum of static and dynamic pressure (plus geodetic)<\/td><td>Total mechanical energy per unit volume<\/td><td>ps + \u00bd\u03c1v\u00b2 + \u03c1gh<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\">2.2 The Bernoulli Connection<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Bernoulli&#8217;s principle, expressed along a streamline for an incompressible, inviscid fluid in steady flow, states:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ps + \u00bd\u03c1v\u00b2 + \u03c1gh = constant (along a streamline)<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">This equation describes the conservation of mechanical energy in a flowing fluid. Energy can be converted between the three forms\u2014static pressure energy, kinetic energy, and potential energy\u2014but their sum remains constant (less frictional losses) along a streamline.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For real fluids in a pump system, Bernoulli&#8217;s equation is modified to account for friction losses (head loss, hf) and the energy added by the pump (head, H). In practice, the total mechanical energy does not remain constant along the flow path because viscous friction dissipates energy as heat, and the pump impeller adds mechanical energy to the fluid:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ps1\/\u03c1g + v1\u00b2\/2g + h1 + H = ps2\/\u03c1g + v2\u00b2\/2g + h2 + hf<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">Where H is the pump head, and hf represents the total system friction losses between points 1 and 2.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2.3 How a Centrifugal Pump Converts Kinetic Energy into Static Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A centrifugal pump operates through a two-stage energy conversion process. First, the rotating impeller blades accelerate the fluid outward from the impeller eye to the periphery, converting mechanical shaft work into kinetic energy in the fluid. The fluid exits the impeller at high velocity. Second, the fluid enters the volute casing, a spiral-shaped chamber of gradually increasing cross-sectional area. As the flow area expands, the fluid decelerates, and by conservation of energy, the reduction in velocity head is converted into an increase in static pressure\u2014a process known as diffusion. The volute therefore functions as a diffuser\u2014converting the velocity head imparted by the impeller into static pressure head that overcomes system resistance\u2014although its geometry differs from an ideal diffuser due to the circumferential pressure distribution inherent in volute design.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2.4 Comparison Table: Static vs. Dynamic vs. Total Pressure<\/h3>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Aspect<\/th><th>Static Pressure (ps)<\/th><th>Dynamic Pressure (pdyn)<\/th><th>Total Pressure (ptot)<\/th><\/tr><\/thead><tbody><tr><td><strong>Definition<\/strong><\/td><td>Pressure exerted uniformly in all directions<\/td><td>Pressure due to fluid motion<\/td><td>Sum of static, dynamic, and geodetic<\/td><\/tr><tr><td><strong>Depends On<\/strong><\/td><td>Fluid state, not velocity<\/td><td>Fluid velocity and density<\/td><td>All three energy components<\/td><\/tr><tr><td><strong>Measured By<\/strong><\/td><td>Pressure gauge (corrected for elevation)<\/td><td>Calculated from velocity and density<\/td><td>Calculated or measured with a Pitot tube<\/td><\/tr><tr><td><strong>In a Centrifugal Pump<\/strong><\/td><td>Inlet and outlet cross-section pressure<\/td><td>Inlet and outlet velocity head<\/td><td>Used to calculate total head developed<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">3. How to Calculate Centrifugal Pump Static Pressure<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">3.1 Inlet (Suction) Static Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The static pressure at the pump inlet cross-section (ps) is calculated from the pressure gauge reading at the suction side (ps,PG), corrected for the elevation difference between the gauge and the pump inlet centerline:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ps = ps,PG + \u03c1 \u00d7 g \u00d7 zs,PG<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">Where:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>ps,PG<\/strong> = pressure gauge reading at the suction measurement tap (in Pa or bar)<\/li>\n\n\n\n<li><strong>\u03c1<\/strong> = density of the pumped liquid (kg\/m\u00b3). For water at 20\u00b0C, \u03c1 \u2248 998 kg\/m\u00b3<\/li>\n\n\n\n<li><strong>g<\/strong> = acceleration due to gravity (9.81 m\/s\u00b2)<\/li>\n\n\n\n<li><strong>zs,PG<\/strong> = vertical distance from the pressure gauge to the pump inlet centerline (m), positive when the gauge is below the pump inlet, negative when above<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Important measurement condition:<\/strong> This formula assumes that the measurement line connecting the pressure tap to the gauge is <strong>filled with the pumped liquid<\/strong>. If the measurement line is filled with gas (air), the hydrostatic head correction term (\u03c1 \u00d7 g \u00d7 zs,PG) must use the density of the gas, not the liquid. In practice, measurement lines must be thoroughly vented to ensure they are completely filled with liquid. Any entrapped air or gas bubbles will introduce measurement errors because the effective density of the fluid column becomes uncertain. For applications involving volatile or hot liquids, condensate pots or diaphragm seals are used to maintain a stable liquid column in the measurement line.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">3.2 Outlet (Discharge) Static Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The static pressure at the pump outlet cross-section (pd) is calculated similarly:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>pd = pd,PG + \u03c1 \u00d7 g \u00d7 zd,PG<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">Where:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>pd,PG<\/strong> = pressure gauge reading at the discharge measurement tap<\/li>\n\n\n\n<li><strong>zd,PG<\/strong> = vertical distance from the pressure gauge to the pump outlet centerline (m)<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\">3.3 Key Parameters Explained<\/h3>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Parameter<\/th><th>Symbol<\/th><th>Unit<\/th><th>Description<\/th><th>Typical Value (Water)<\/th><\/tr><\/thead><tbody><tr><td>Fluid density<\/td><td>\u03c1<\/td><td>kg\/m\u00b3<\/td><td>Mass per unit volume; temperature-dependent<\/td><td>~998 kg\/m\u00b3 at 20\u00b0C<\/td><\/tr><tr><td>Gravity<\/td><td>g<\/td><td>m\/s\u00b2<\/td><td>Standard gravitational acceleration<\/td><td>9.81<\/td><\/tr><tr><td>Elevation correction<\/td><td>z<\/td><td>m<\/td><td>Vertical distance from gauge to pump cross-section<\/td><td>Application-dependent<\/td><\/tr><tr><td>Barometric pressure<\/td><td>pb<\/td><td>Pa or bar<\/td><td>Local atmospheric pressure<\/td><td>~101,325 Pa at sea level<\/td><\/tr><tr><td>Vapour pressure<\/td><td>pV<\/td><td>Pa or bar<\/td><td>Pressure at which liquid vaporises at operating temperature<\/td><td>~2,337 Pa for water at 20\u00b0C<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\">3.4 Liquid-Filled vs. Gas-Filled Measurement Lines<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The standard EN 12723:2000 distinguishes between two measurement configurations:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Liquid-filled measurement line:<\/strong> The line connecting the pressure tap to the gauge is filled with the pumped liquid. The correction term uses the liquid density \u03c1. This is the standard configuration for most pump applications.<\/li>\n\n\n\n<li><strong>Gas-filled measurement line:<\/strong> The line is filled with air or another gas. The correction term uses the gas density \u03c1gas, which is approximately three orders of magnitude smaller than the liquid density. In this case, the hydrostatic correction may be negligible if the elevation difference is small.<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\">3.5 Barometric Pressure and Vapour Pressure Considerations<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">For NPSH calculations, the inlet static pressure must be expressed as an absolute pressure, not a gauge pressure. This requires adding the local barometric pressure to the gauge reading. Additionally, the vapour pressure of the pumped liquid at the operating temperature must be known, as it determines the pressure below which cavitation will occur. Both parameters are temperature-dependent and must be verified for each application.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">4. Step-by-Step Calculation Examples<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Example 1: Suction Static Pressure (Liquid-Filled Measurement Line)<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A centrifugal pump draws water at 20\u00b0C from an open tank. The suction pressure gauge, located 0.4 m below the pump inlet centerline, reads -0.2 bar (gauge). Calculate the static pressure at the pump inlet cross-section.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Given:<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>ps,PG = -0.2 bar = -20,000 Pa<\/li>\n\n\n\n<li>zs,PG = +0.4 m (gauge is below pump inlet \u2192 positive)<\/li>\n\n\n\n<li>\u03c1 = 998 kg\/m\u00b3 (water at 20\u00b0C)<\/li>\n\n\n\n<li>g = 9.81 m\/s\u00b2<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Calculation:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ps = ps,PG + \u03c1 \u00d7 g \u00d7 zs,PG\nps = -20,000 + (998 \u00d7 9.81 \u00d7 0.4)\nps = -20,000 + 3,916\nps = -16,084 Pa \u2248 -0.161 bar (gauge)<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">The corrected static pressure at the pump inlet is -0.161 bar (gauge), which is higher (less negative) than the gauge reading of -0.2 bar because the gauge is located below the pump inlet, and the liquid column in the measurement line adds hydrostatic head.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Example 2: Discharge Static Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The discharge pressure gauge, located 0.6 m above the pump outlet centerline, reads 5.5 bar (gauge). Calculate the static pressure at the pump outlet cross-section.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Given:<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>pd,PG = 5.5 bar = 550,000 Pa<\/li>\n\n\n\n<li>zd,PG = -0.6 m (gauge is above pump outlet \u2192 negative)<\/li>\n\n\n\n<li>\u03c1 = 998 kg\/m\u00b3<\/li>\n\n\n\n<li>g = 9.81 m\/s\u00b2<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Calculation:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>pd = pd,PG + \u03c1 \u00d7 g \u00d7 zd,PG\npd = 550,000 + (998 \u00d7 9.81 \u00d7 (-0.6))\npd = 550,000 - 5,874\npd = 544,126 Pa \u2248 5.44 bar (gauge)<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">The corrected static pressure at the pump outlet is 5.44 bar (gauge), which is lower than the gauge reading because the gauge is positioned above the pump outlet.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Example 3: Gauge to Absolute Pressure Conversion<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Convert the calculated suction static pressure from Example 1 to absolute pressure for NPSH analysis. Assume the pump is at sea level.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Given:<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>ps (gauge) = -16,084 Pa<\/li>\n\n\n\n<li>pb (atmospheric) = 101,325 Pa<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Calculation:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>ps (absolute) = ps (gauge) + pb\nps (absolute) = -16,084 + 101,325\nps (absolute) = 85,241 Pa \u2248 0.852 bar (absolute)<\/code><\/pre>\n\n\n\n<h3 class=\"wp-block-heading\">Example 4: From Static Pressure to Pump Total Head<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Calculate the pump total head (H) using the corrected static pressures from Examples 1 and 2. The suction pipe diameter is 150 mm, and the discharge pipe diameter is 100 mm. The flow rate is 80 m\u00b3\/h. The geodetic elevation difference between the suction and discharge cross-sections is negligible.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Given:<\/strong><\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>ps = -16,084 Pa (from Example 1)<\/li>\n\n\n\n<li>pd = 544,126 Pa (from Example 2)<\/li>\n\n\n\n<li>Q = 80 m\u00b3\/h = 0.0222 m\u00b3\/s<\/li>\n\n\n\n<li>Ds = 150 mm \u2192 As = \u03c0 \u00d7 (0.15\/2)\u00b2 = 0.0177 m\u00b2<\/li>\n\n\n\n<li>Dd = 100 mm \u2192 Ad = \u03c0 \u00d7 (0.10\/2)\u00b2 = 0.00785 m\u00b2<\/li>\n\n\n\n<li>\u03c1 = 998 kg\/m\u00b3<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 1: Calculate velocities:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>vs = Q \/ As = 0.0222 \/ 0.0177 = 1.25 m\/s\nvd = Q \/ Ad = 0.0222 \/ 0.00785 = 2.83 m\/s<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 2: Calculate velocity heads:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>vs\u00b2\/2g = (1.25)\u00b2 \/ (2 \u00d7 9.81) = 0.080 m\nvd\u00b2\/2g = (2.83)\u00b2 \/ (2 \u00d7 9.81) = 0.408 m<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 3: Calculate total head:<\/strong><\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>H = (pd - ps) \/ (\u03c1 \u00d7 g) + (vd\u00b2 - vs\u00b2) \/ (2g)\nH = (544,126 - (-16,084)) \/ (998 \u00d7 9.81) + (0.408 - 0.080)\nH = 560,210 \/ 9,790 + 0.328\nH = 57.2 + 0.328 = 57.5 m<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">The pump total head is 57.5 m. The velocity head correction contributes 0.33 m\u2014approximately 0.6% of the total head in this example. However, this proportion is application-dependent: for pumps with larger diameter ratios (e.g., 200 mm suction and 80 mm discharge) or low-head, high-flow designs, the velocity head correction can represent 5\u201310% of the total head and must not be neglected.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">5. How Does Static Pressure Affect NPSH and Cavitation in a Centrifugal Pump?<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">5.1 What Is NPSH?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Net Positive Suction Head (NPSH) quantifies the margin between the absolute pressure available at the pump inlet and the vapour pressure of the pumped liquid. It is defined in two forms:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>NPSHA (Net Positive Suction Head Available):<\/strong> The absolute static head at the pump suction, less the vapour pressure head, under the actual system operating conditions.<\/li>\n\n\n\n<li><strong>NPSHR (Net Positive Suction Head Required):<\/strong> The minimum NPSH required by the pump to prevent cavitation, as determined by the manufacturer through testing. The Hydraulic Institute defines NPSHR as the value at which the pump total head has decreased by 3% due to cavitation.<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\">5.2 The Direct Link Between Inlet Static Pressure and NPSHA<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The NPSHA equation is:<\/p>\n\n\n\n<pre class=\"wp-block-code\"><code>NPSHA = (ps(abs) \/ \u03c1g) + (vs\u00b2 \/ 2g) - (pV \/ \u03c1g)<\/code><\/pre>\n\n\n\n<p class=\"wp-block-paragraph\">Where ps(abs) is the absolute static pressure at the pump inlet cross-section, calculated as demonstrated in Section 4, Example 3. This direct dependence on static pressure means that any error in measuring or calculating ps propagates directly into the NPSHA value.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">5.3 When Static Pressure Falls Below Vapour Pressure: Cavitation<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Cavitation occurs when the local absolute pressure in the pump falls below the vapour pressure of the liquid. Vapour bubbles form in the low-pressure region at the impeller inlet, then collapse violently as they travel downstream into higher-pressure zones. The bubble collapse produces localised pressure shock waves that pit the impeller surface and generate the characteristic noise and vibration of cavitation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Cavitation is not merely a performance issue\u2014it can destroy an impeller within weeks, significantly shortening pump service life. The relationship between static pressure and cavitation risk is fundamental: maintaining sufficient NPSHA ensures that the absolute static pressure at the impeller inlet remains above the vapour pressure, preventing bubble formation.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">5.4 Practical Guidance: Monitoring Inlet Static Pressure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Operators should trend the suction static pressure over time. A gradual decline in suction pressure, at constant flow rate, can signal:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Clogging of the suction strainer or intake screen<\/li>\n\n\n\n<li>Declining liquid level in the supply tank<\/li>\n\n\n\n<li>Fouling or scaling in the suction piping increasing friction losses<\/li>\n\n\n\n<li>Changes in fluid temperature affecting vapour pressure<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Early detection of these trends through static pressure monitoring enables corrective action before cavitation damage occurs. A suction pressure that trends 5\u201310% below the design value over several months is a reliable warning signal. <\/p>\n\n\n\n<h2 class=\"wp-block-heading\">6. Frequently Asked Questions<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q1: What is the difference between static pressure and total pressure in a centrifugal pump?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: Static pressure is the pressure acting uniformly in all directions, independent of fluid velocity. Total pressure is the sum of static pressure, dynamic pressure (velocity head), and geodetic elevation head. In centrifugal pump technology, the term &#8220;pressure&#8221; always refers to static pressure per DIN EN ISO 17769-1:2012.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q2: How do I calculate the static pressure at the pump inlet?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: Use the formula ps = ps,PG + \u03c1 \u00d7 g \u00d7 zs,PG, where ps,PG is the suction gauge reading, \u03c1 is the fluid density, g is gravitational acceleration, and zs,PG is the vertical distance from the gauge to the pump inlet centerline (positive when the gauge is below the pump).<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q3: Why does my pressure gauge not measure velocity head?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: A pressure gauge connected perpendicular to the flow measures only the static pressure acting on the pipe wall. It cannot measure the kinetic energy per unit volume (\u00bd\u03c1v\u00b2) of the moving fluid. The velocity head must be calculated separately from the flow rate and pipe cross-sectional area.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q4: What is the difference between gauge pressure and absolute pressure?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: Gauge pressure is measured relative to local atmospheric pressure. Absolute pressure is measured relative to a perfect vacuum. For NPSH calculations, absolute pressure must be used. Convert using: Absolute Pressure = Gauge Pressure + Atmospheric Pressure.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q5: How does static pressure relate to NPSH and cavitation?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: NPSHA depends directly on the absolute static pressure at the pump inlet. When the local absolute pressure drops below the liquid&#8217;s vapour pressure, cavitation occurs\u2014vapour bubbles form and collapse, causing pitting damage to the impeller.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q6: What correction is needed when the pressure gauge is not at the pump centerline?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: The hydrostatic head between the gauge and the pump cross-section must be added or subtracted. If the gauge is below the pump centerline, the fluid column adds pressure; if above, it subtracts pressure. The correction is \u03c1 \u00d7 g \u00d7 z, where z is the vertical distance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q7: Does the measurement line fluid affect the static pressure calculation?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: Yes. Liquid-filled measurement lines use the pumped liquid density (\u03c1) for the hydrostatic correction. Gas-filled measurement lines use the gas density (\u03c1gas \u2248 1.2 kg\/m\u00b3 for air), making the correction negligible for small elevation differences. In practice, measurement lines must be vented to eliminate air pockets that cause uncertain effective density in the fluid column.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Q8: How do I calculate pump total head from static pressure measurements?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A: Pump total head H = (pd &#8211; ps)\/(\u03c1g) + (vd\u00b2 &#8211; vs\u00b2)\/(2g) + (hd &#8211; hs), where pd and ps are the corrected discharge and suction static pressures, vd and vs are the discharge and suction velocities, and hd &#8211; hs is the geodetic elevation difference between the discharge and suction cross-sections.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">7. Conclusion<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The static pressure in a centrifugal pump is the foundation upon which pump performance measurement, cavitation analysis, and total head calculation are built. The term &#8220;pressure&#8221; in centrifugal pump technology refers exclusively to static pressure, as established by DIN EN ISO 17769-1:2012. Static pressure coexists with dynamic pressure and geodetic elevation head\u2014the three components of a fluid&#8217;s total mechanical energy per unit volume described by Bernoulli&#8217;s principle.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Calculating the static pressure at the pump inlet and outlet cross-sections requires correcting the pressure gauge reading for the elevation difference between the gauge and the pump centerline. For NPSH analysis, the static pressure must be expressed in absolute terms by adding the local atmospheric pressure to the gauge reading. The relationship between inlet static pressure and NPSHA is direct and consequential: insufficient static pressure at the suction leads to cavitation, impeller damage, and premature pump failure.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1024\" height=\"412\" src=\"https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-1024x412.webp\" alt=\"Changyu Pump\" class=\"wp-image-2555\" srcset=\"https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-1024x412.webp 1024w, https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-300x121.webp 300w, https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-768x309.webp 768w, https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-1536x618.webp 1536w, https:\/\/changyupump.com\/wp-content\/uploads\/2025\/12\/Changyu-Pump-2-2048x825.webp 2048w\" sizes=\"auto, (max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The formulas and worked examples provided in this guide\u2014together with the distinction between liquid-filled and gas-filled measurement lines\u2014equip engineers and technicians with the tools to correctly measure, calculate, and interpret pump static pressure in any operating environment. <a href=\"https:\/\/changyupump.com\/contacts\/\">Contact Changyu Pump <\/a>for technical support on pump pressure measurement, NPSH evaluation, and system troubleshooting.<\/p>\n\n\n<div class=\"wp-block-kadence-advanced-form wp-block-kadence-advanced-form1246-cpt-id kb-adv-form-label-style-normal kb-adv-form-input-size-standard kb-form-basic-style\"><form id=\"kb-adv-form-1246-cpt-id\" class=\"kb-advanced-form\" method=\"post\">\n<style>.kb-row-layout-id16_395842-3c > .kt-row-column-wrap{align-content:start;}:where(.kb-row-layout-id16_395842-3c > .kt-row-column-wrap) > .wp-block-kadence-column{justify-content:start;}.kb-row-layout-id16_395842-3c > .kt-row-column-wrap{column-gap:var(--global-kb-gap-md, 2rem);row-gap:var(--global-kb-gap-md, 2rem);padding-top:0px;padding-right:0px;padding-bottom:0px;padding-left:0px;grid-template-columns:repeat(2, minmax(0, 1fr));}.kb-row-layout-id16_395842-3c > .kt-row-layout-overlay{opacity:0.30;}@media all and (max-width: 1024px){.kb-row-layout-id16_395842-3c > .kt-row-column-wrap{grid-template-columns:repeat(2, minmax(0, 1fr));}}@media all and (max-width: 767px){.kb-row-layout-id16_395842-3c > .kt-row-column-wrap{grid-template-columns:minmax(0, 1fr);}}<\/style><div class=\"kb-row-layout-wrap kb-row-layout-id16_395842-3c alignnone wp-block-kadence-rowlayout\"><div class=\"kt-row-column-wrap kt-has-2-columns kt-row-layout-equal kt-tab-layout-inherit kt-mobile-layout-row kt-row-valign-top\">\n<style>.kadence-column16_3a38e5-5d > .kt-inside-inner-col,.kadence-column16_3a38e5-5d > .kt-inside-inner-col:before{border-top-left-radius:0px;border-top-right-radius:0px;border-bottom-right-radius:0px;border-bottom-left-radius:0px;}.kadence-column16_3a38e5-5d > .kt-inside-inner-col{column-gap:var(--global-kb-gap-sm, 1rem);}.kadence-column16_3a38e5-5d > .kt-inside-inner-col{flex-direction:column;}.kadence-column16_3a38e5-5d > .kt-inside-inner-col > .aligncenter{width:100%;}.kadence-column16_3a38e5-5d > .kt-inside-inner-col:before{opacity:0.3;}.kadence-column16_3a38e5-5d{position:relative;}@media all and (max-width: 1024px){.kadence-column16_3a38e5-5d > .kt-inside-inner-col{flex-direction:column;justify-content:center;}}@media all and (max-width: 767px){.kadence-column16_3a38e5-5d > .kt-inside-inner-col{flex-direction:column;justify-content:center;}}<\/style>\n<div class=\"wp-block-kadence-column kadence-column16_3a38e5-5d\"><div class=\"kt-inside-inner-col\"><div class=\"kb-adv-form-field kb-adv-form-text-type-input kb-adv-form-infield-type-input kb-field124600b147-f8 wp-block-kadence-advanced-form-text\"><label class=\"kb-adv-form-label\" for=\"field124600b147-f8\">Name<\/label><input name=\"field00b147-f8\" id=\"field124600b147-f8\" data-label=\"Name\" type=\"text\" placeholder=\"\" value=\"\" data-type=\"text\" class=\"kb-field kb-text-field\" data-required=\"no\" \/><\/div><\/div><\/div>\n\n\n<style>.kadence-column16_be3802-0b > .kt-inside-inner-col,.kadence-column16_be3802-0b > .kt-inside-inner-col:before{border-top-left-radius:0px;border-top-right-radius:0px;border-bottom-right-radius:0px;border-bottom-left-radius:0px;}.kadence-column16_be3802-0b > .kt-inside-inner-col{column-gap:var(--global-kb-gap-sm, 1rem);}.kadence-column16_be3802-0b > .kt-inside-inner-col{flex-direction:column;}.kadence-column16_be3802-0b > .kt-inside-inner-col > .aligncenter{width:100%;}.kadence-column16_be3802-0b > .kt-inside-inner-col:before{opacity:0.3;}.kadence-column16_be3802-0b{position:relative;}@media all and (max-width: 1024px){.kadence-column16_be3802-0b > .kt-inside-inner-col{flex-direction:column;justify-content:center;}}@media all and (max-width: 767px){.kadence-column16_be3802-0b > .kt-inside-inner-col{flex-direction:column;justify-content:center;}}<\/style>\n<div class=\"wp-block-kadence-column kadence-column16_be3802-0b\"><div class=\"kt-inside-inner-col\"><div class=\"kb-adv-form-field kb-adv-form-text-type-input kb-adv-form-infield-type-input kb-field124648086d-59 wp-block-kadence-advanced-form-email\"><label class=\"kb-adv-form-label\" for=\"field124648086d-59\">Email<span class=\"kb-adv-form-required\">*<\/span><\/label><input name=\"field48086d-59\" id=\"field124648086d-59\" data-label=\"Email\" type=\"email\" placeholder=\"\" value=\"\" data-type=\"email\" class=\"kb-field kb-email-field\" data-required=\"yes\" required aria-required=\"true\"\/><\/div><\/div><\/div>\n\n<\/div><\/div>\n\n<div class=\"kb-adv-form-field kb-adv-form-text-type-input kb-adv-form-infield-type-input kb-field124697066f-d3 wp-block-kadence-advanced-form-text\"><label class=\"kb-adv-form-label\" for=\"field124697066f-d3\">Whatsapp\/Phone<\/label><input name=\"field97066f-d3\" id=\"field124697066f-d3\" data-label=\"Whatsapp\/Phone\" type=\"text\" placeholder=\"\" value=\"\" data-type=\"text\" class=\"kb-field kb-text-field\" data-required=\"no\" \/><\/div>\n\n<div class=\"kb-adv-form-field kb-adv-form-text-type-input kb-adv-form-infield-type-input kb-field1246ae3276-7e wp-block-kadence-advanced-form-textarea\"><label class=\"kb-adv-form-label\" for=\"field1246ae3276-7e\">Message<span class=\"kb-adv-form-required\">*<\/span><\/label><textarea name=\"fieldae3276-7e\" id=\"field1246ae3276-7e\" rows=\"4\"  data-label=\"Message\" placeholder=\"\" data-type=\"textarea\" class=\"kb-field kb-textarea-field\" data-required=\"yes\" required aria-required=\"true\"><\/textarea><\/div>\n\n<style>ul.menu .kb-submit-field .kb-btnd4ade1-86.kb-button{width:initial;}.kb-submit-field .kb-btnd4ade1-86.kb-button{background:var(--global-palette1, #3182CE);}.kb-submit-field .kb-btnd4ade1-86.kb-button:hover, .kb-submit-field .kb-btnd4ade1-86.kb-button:focus{background:var(--global-palette2, #2B6CB0);}.kb-submit-field.kb-fieldd4ade1-86{justify-content:flex-start;}<\/style><div class=\"kb-adv-form-field kb-submit-field kb-fieldd4ade1-86 wp-block-kadence-advanced-form-submit\"><button class=\"kb-button kt-button button kb-adv-form-submit-button kb-btnd4ade1-86 kt-btn-size-standard kt-btn-width-type-auto kb-btn-global-inherit kt-btn-has-text-true kt-btn-has-svg-false wp-block-button__link\" type=\"submit\"><span class=\"kt-btn-inner-text\">Submit<\/span><\/button><\/div>\n<input type=\"hidden\" name=\"_kb_adv_form_post_id\" value=\"1246\"><input type=\"hidden\" name=\"action\" value=\"kb_process_advanced_form_submit\"><input type=\"hidden\" name=\"_kb_adv_form_id\" value=\"1246-cpt-id\"><\/form><\/div>\n\n\n<script type=\"application\/ld+json\">\n{\n  \"@context\": \"https:\/\/schema.org\",\n  \"@type\": \"FAQPage\",\n  \"mainEntity\": [\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What is the difference between static pressure and total pressure in a centrifugal pump?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Static pressure is the pressure acting uniformly in all directions, independent of fluid velocity. Total pressure is the sum of static pressure, dynamic pressure (velocity head), and geodetic elevation head. In centrifugal pump technology, the term 'pressure' always refers to static pressure per DIN EN ISO 17769-1:2012.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"How do I calculate the static pressure at the pump inlet?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Use the formula ps = ps,PG + \u03c1 \u00d7 g \u00d7 zs,PG, where ps,PG is the suction gauge reading, \u03c1 is the fluid density, g is gravitational acceleration, and zs,PG is the vertical distance from the gauge to the pump inlet centerline (positive when the gauge is below the pump).\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Why does my pressure gauge not measure velocity head?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"A pressure gauge connected perpendicular to the flow measures only the static pressure acting on the pipe wall. It cannot measure the kinetic energy per unit volume (\u00bd\u03c1v\u00b2) of the moving fluid. The velocity head must be calculated separately from the flow rate and pipe cross-sectional area.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What is the difference between gauge pressure and absolute pressure?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Gauge pressure is measured relative to local atmospheric pressure. Absolute pressure is measured relative to a perfect vacuum. For NPSH calculations, absolute pressure must be used. Convert using: Absolute Pressure = Gauge Pressure + Atmospheric Pressure.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"How does static pressure relate to NPSH and cavitation?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"NPSHA depends directly on the absolute static pressure at the pump inlet. When the local absolute pressure drops below the liquid's vapour pressure, cavitation occurs\u2014vapour bubbles form and collapse, causing pitting damage to the impeller.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"What correction is needed when the pressure gauge is not at the pump centerline?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"The hydrostatic head between the gauge and the pump cross-section must be added or subtracted. If the gauge is below the pump centerline, the fluid column adds pressure; if above, it subtracts pressure. The correction is \u03c1 \u00d7 g \u00d7 z, where z is the vertical distance.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"Does the measurement line fluid affect the static pressure calculation?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Yes. Liquid-filled measurement lines use the pumped liquid density (\u03c1) for the hydrostatic correction. Gas-filled measurement lines use the gas density (\u03c1gas \u2248 1.2 kg\/m\u00b3 for air), making the correction negligible for small elevation differences. In practice, measurement lines must be vented to eliminate air pockets that cause uncertain effective density in the fluid column.\"\n      }\n    },\n    {\n      \"@type\": \"Question\",\n      \"name\": \"How do I calculate pump total head from static pressure measurements?\",\n      \"acceptedAnswer\": {\n        \"@type\": \"Answer\",\n        \"text\": \"Pump total head H = (pd - ps)\/(\u03c1g) + (vd\u00b2 - vs\u00b2)\/(2g) + (hd - hs), where pd and ps are the corrected discharge and suction static pressures, vd and vs are the discharge and suction velocities, and hd - hs is the geodetic elevation difference between the discharge and suction cross-sections.\"\n      }\n    }\n  ]\n}\n<\/script>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Introduction In centrifugal pump technology, the term pressure always refers to static pressure. This definition, established by&#8230;<\/p>","protected":false},"author":2,"featured_media":5636,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_kad_blocks_custom_css":"","_kad_blocks_head_custom_js":"","_kad_blocks_body_custom_js":"","_kad_blocks_footer_custom_js":"","_kadence_starter_templates_imported_post":false,"_kad_post_transparent":"","_kad_post_title":"","_kad_post_layout":"","_kad_post_sidebar_id":"","_kad_post_content_style":"","_kad_post_vertical_padding":"","_kad_post_feature":"","_kad_post_feature_position":"","_kad_post_header":false,"_kad_post_footer":false,"footnotes":""},"categories":[12],"tags":[],"class_list":["post-5184","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"acf":[],"taxonomy_info":{"category":[{"value":12,"label":"Blog"}]},"featured_image_src_large":["https:\/\/changyupump.com\/wp-content\/uploads\/2026\/05\/What-Is-the-Static-Pressure-of-the-Centrifugal-Pump-and-How-to-Calculate-It.webp",1000,750,false],"author_info":{"display_name":"Changyu_","author_link":"https:\/\/changyupump.com\/id\/author\/changyu_\/"},"comment_info":1,"category_info":[{"term_id":12,"name":"Blog","slug":"blog","term_group":0,"term_taxonomy_id":12,"taxonomy":"category","description":"","parent":0,"count":112,"filter":"raw","cat_ID":12,"category_count":112,"category_description":"","cat_name":"Blog","category_nicename":"blog","category_parent":0}],"tag_info":false,"_links":{"self":[{"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/posts\/5184","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/comments?post=5184"}],"version-history":[{"count":5,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/posts\/5184\/revisions"}],"predecessor-version":[{"id":5639,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/posts\/5184\/revisions\/5639"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/media\/5636"}],"wp:attachment":[{"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/media?parent=5184"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/categories?post=5184"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/changyupump.com\/id\/wp-json\/wp\/v2\/tags?post=5184"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}